USRP-2974 Getting Started Guide - Revision history

NeelPandeya: /* Install and Setup the Software Tools on the onboard computer (SoM-System on Module) */

2019-07-23T12:28:04Z

‎Install and Setup the Software Tools on the onboard computer (SoM-System on Module)

NeelPandeya: /* Note on USRP-2974 Rev A Hardware */

2019-07-15T11:37:02Z

‎Note on USRP-2974 Rev A Hardware

NeelPandeya: /* Note on USRP-2974 Rev A Hardware */

2019-06-04T12:15:32Z

‎Note on USRP-2974 Rev A Hardware

JoseLoera: /* Kit Contents */

2019-06-01T15:16:29Z

‎Kit Contents

JoseLoera: /* Kit Contents */

2019-06-01T15:15:44Z

‎Kit Contents

JoseLoera: /* Additional Resources */

2019-06-01T15:11:18Z

‎Additional Resources

JoseLoera: /* Basic Connectivity */

2019-06-01T15:10:32Z

‎Basic Connectivity

JoseLoera: Created page with "==Kit Contents== * NI USRP-2974 * 30 dB SMA Attenuator * SMA-male to SMA-male Cable * Power Supply * Getting Started Guide {| ||center |..."

2019-06-01T14:42:16Z

Created page with "==Kit Contents== * NI USRP-2974 * 30 dB SMA Attenuator * SMA-male to SMA-male Cable * Power Supply * Getting Started Guide {| ||center |..."

New page

==Kit Contents==
* NI USRP-2974
* 30 dB SMA Attenuator
* SMA-male to SMA-male Cable
* Power Supply
* Getting Started Guide
{|
||[[File:USRP_2974_frt_dia.jpg|250px|center]]
|}

==Verify the Contents of Your Kit==
Make sure that your kit contains all the items listed above. If any items are missing, please contact your sales agent.

==Unpacking the Kit==
1. To prevent electrostatic discharge (ESD) from damaging the device, ground yourself using a grounding strap or by holding a grounded object, such as your computer chassis.

2. Remove the device from the package and inspect the device for loose components or any
other sign of damage.

3. Never touch the exposed pins of connectors.

4. Unpack any other items and documentation from the kit.

'''NOTE:''' Do not install a device if it appears damaged in any way. Store the device in the antistatic package when the device is not in use.

==Proper Care and Handling==
All NI products are individually tested before shipment. The USRP™ is guaranteed to be functional at the time it is received by the customer. Improper use or handling of the USRP™ can easily cause the device to become non-functional. Listed below are some examples of actions which can prevent damage to the unit:

*Always properly terminate the transmit port with an antenna or 50Ω load.
*Always handle the USRP with proper anti-static methods.
*Never allow the USRP to directly or indirectly come into contact with any voltage spikes.
*Never allow any water, or condensing moisture, to come into contact with the USRP.
*Always use caution with FPGA, firmware, or software modifications.
{|
|style="padding-left:10px; padding-right:10px; padding-bottom:10px;" |[[File:Caution.png|24px|center]]
|style="padding-left:10px; padding-right:10px; padding-bottom:10px;" |Never apply more than '''+10 dBm''' of power into RF ports RF0 and RF1.
|-
|style="padding-left:10px; padding-right:10px; padding-bottom:10px;" |[[File:Caution.png|24px|center]]
|style="padding-left:10px; padding-right:10px; padding-bottom:10px;" |Never apply more than '''+15 dBm''' of power into the REF IN input.
|-
|style="padding-left:10px; padding-right:10px; padding-bottom:10px;" |[[File:Caution.png|24px|center]]
|style="padding-left:10px; padding-right:10px; padding-bottom:10px;" |Never apply more than '''-15 dBm''' of power into the GPS ANT input.
|-
|style="padding-left:10px; padding-right:10px; padding-bottom:10px;" |[[File:Caution.png|24px|center]]
|style="padding-left:10px; padding-right:10px; padding-bottom:10px;" |Always use at least 30dB attenuation if operating in loopback configuration
|-
|}

==Install and Setup the Software Tools on the onboard computer (SoM-System on Module)==
In order to use your Universal Software Radio Peripheral (USRP™), you must have the software tools correctly installed and configured on the SoM. A step-by-step guide for doing this is available at the [https://kb.ettus.com/Building_and_Installing_the_USRP_Open-Source_Toolchain_(UHD_and_GNU_Radio)_on_Linux Building and Installing the USRP Open-Source Toolchain (UHD and GNU Radio) on the Linux] Application Note. '''Release 3.15.0''' or later of the USRP Hardware Driver, UHD, is needed.

==Basic Connectivity==
This USRP-2974 host supports multiple, high-speed, low-latency interface options to the FPGA. To setup the device, follow these basic instructions:
* Configure the host ethernet adapter (enp1s0f0) to use an IP address of 192.168.40.1 and a subnet mask of 255.255.255.0
* Configure the host ethernet adapter (enp1s0f1) to use an IP address of 192.168.30.1 and a subnet mask of 255.255.255.0 (loopback with SFP+ cable needed)
* To test communications, ping the USRP FPGA at address "192.168.40.2" or “192.168.30.2”

For more details on network setup, including PCIe connectivity, please see the section [[NI_USRP-2974_Hardware_Resource_0#Interfaces_and_Connectivity|Interfaces and Connectivity]] of the NI USRP-2974 Hardware Resources page.

==Test and Verify the Operation of the USRP==
Once the software tools are installed on the onboard computer, verify the correct operation of the USRP by running the utility programs on the onboard computer. More information is available at the [https://kb.ettus.com/Verifying_the_Operation_of_the_USRP_Using_UHD_and_GNU_Radio Verifying the Operation of the USRP Using UHD and GNU Radio] Application Note.

==Enabling PXE Boot==

===Legacy PXE Boot===
* When rebooting the USRP-2974 open BIOS with DEL and go to Boot tab
* Enable PXE Network Boot with Legacy option, restart the system
* Go into the BIOS’ Boot tab and set IBA CL Slot 00FE v0105 as first boot option, restart the system

===UEFI PXE Boot===
* When rebooting the USRP-2974 open BIOS with DEL and go to Boot tab
* Enable PXE Network Boot with UEFI option, restart the system
* Go into the BIOS’ Boot tab and set IPv4 as first boot option, restart the system

==NI USRP RIO PCIe Support==

If you are connecting the USRP-2974 through the PCIe interface, then complete this section.

If you are connecting the USRP-2974 through the 1G or 10G Ethernet connection then do '''NOT''' complete this section.

# Installer and commands taken from [https://files.ettus.com/manual/page_ni_rio_kernel.html https://files.ettus.com/manual/page_ni_rio_kernel.html]
# Extract the installer and install as described (note the _ instead of – in the folder name)
# Enable or disable the PCIe link
##<code>$ sudo /usr/local/bin/niusrprio_pcie start</code>
##<code>$ sudo /usr/local/bin/niusrprio_pcie stop </code>
# Check the status
##<code>$ sudo /usr/local/bin/niusrprio_pcie status</code>
# see the connection over PCIe with
##<code>$ uhd_find_devices</code>

==Note on USRP-2974 Rev A Hardware==
To find out if you have a '''"Rev A"''' hardware version of the USRP-2974 check the last character of the part number on the USRP-2974. E.g. "146873'''A'''"

To fully support Rev A with UHD software, install UHD as explained and run the following command:

$ /usr/local/lib/uhd/utils/usrp_burn_mb_eeprom --args=”addr=192.168.40.2” --value=”product=31131”

After a reboot run:

$ uhd_find_devices</code>

Under the product category section you will see the following:
“NI-2974”.

==Technical Support and Community Knowledge Base==

Technical support for USRP hardware is available through email only. If the product arrived in a nonfunctional state or you require technical assistance, please contact [mailto:support@ettus.com support@ettus.com]. Please allow 24 to 48 hours for response by email, depending on holidays and weekends, although we are often able to reply more quickly than that.

We also recommend that you subscribe to the community mailing lists. The mailing lists have a responsive and knowledgeable community of hundreds of developers and technical users who are located around the world. When you join the community, you will be connected to this group of people who can help you learn about SDR and respond to your technical and specific questions. Often your question can be answered quickly on the mailing lists. Each mailing list also provides an archive of all past conversations and discussions going back many years. Your question or problem may have already been addressed before, and a relevant or helpful solution may already exist in the archive.

Discussions involving the USRP hardware and the UHD software itself are best addressed through the '''usrp-users''' mailing list at [http://usrp-users.ettus.com http://usrp-users.ettus.com].

Discussions involving the use of [http://gnuradio.org/ GNU Radio] with USRP hardware and UHD software are best addressed through the '''discuss-gnuradio''' mailing list at [https://lists.gnu.org/mailman/listinfo/discussgnuradio https://lists.gnu.org/mailman/listinfo/discussgnuradio].

Discussions involving the use of [http://openbts.org/ OpenBTS®] with USRP hardware and UHD software are best addressed through the '''openbts-discuss''' mailing list at [https://lists.sourceforge.net/lists/listinfo/openbtsdiscuss https://lists.sourceforge.net/lists/listinfo/openbtsdiscuss].

The support page on our website is located at [https://www.ettus.com/support https://www.ettus.com/support]. The Knowledge Base is located at [https://kb.ettus.com https://kb.ettus.com].

==Legal Considerations==
Every country has laws governing the transmission and reception of radio signals. Users are solely responsible for insuring they use their USRP system in compliance with all applicable laws and regulations. Before attempting to transmit and/or receive on any frequency, we recommend that you determine what licenses may be required and what restrictions may apply.

*NOTE: This USRP product is a piece of test equipment.

==Sales and Ordering Support==

If you have any non-technical questions related to your order, then please contact us by email at [mailto:orders@ettus.com orders@ettus.com]. Please be sure to include your order number and the serial number of your USRP.

==Terms and Conditions of Sale==
Terms and conditions of sale can be accessed online at the following link: http://www.ettus.com/legal/terms-and-conditions-of-sale

==Additional Resources==

* [[NI_USRP-2974_Hardware_Resource_00 | USRP-2974 Hardware Resource]]
* http://www.ni.com/pdf/manuals/377416c.pdf

[[Category:Getting Started Guides]]

@@ Line 53: / Line 53: @@
 ==Install and Setup the Software Tools on the onboard computer (SoM-System on Module)==
-In order to use your Universal Software Radio Peripheral (USRP™), you must have the software tools correctly installed and configured on the SoM. A step-by-step guide for doing this is available at the [https://kb.ettus.com/Building_and_Installing_the_USRP_Open-Source_Toolchain_(UHD_and_GNU_Radio)_on_Linux Building and Installing the USRP Open-Source Toolchain (UHD and GNU Radio) on the Linux] Application Note. '''Release 3.15.0''' or later of the USRP Hardware Driver, UHD, is needed.
+In order to use your Universal Software Radio Peripheral (USRP™), you must have the software tools correctly installed and configured on the SoM. A step-by-step guide for doing this is available at the [https://kb.ettus.com/Building_and_Installing_the_USRP_Open-Source_Toolchain_(UHD_and_GNU_Radio)_on_Linux Building and Installing the USRP Open-Source Toolchain (UHD and GNU Radio) on the Linux] Application Note. '''Release 3.14.1.0''' or later of the USRP Hardware Driver (UHD), is needed.
 ==Basic Connectivity==

@@ Line 103: / Line 103: @@
 After a reboot run:
-     $ uhd_find_devices</code>
+     $ uhd_find_devices
 Under the product category section you will see the following:

@@ Line 99: / Line 99: @@
 To fully support Rev A with UHD software, install UHD as explained and run the following command:
-     $ /usr/local/lib/uhd/utils/usrp_burn_mb_eeprom --args=”addr=192.168.40.2” --value=”product=31131”
+     $ /usr/local/lib/uhd/utils/usrp_burn_mb_eeprom --args="addr=192.168.40.2" --value="product=31131"
 After a reboot run:
@@ Line 106: / Line 106: @@
 Under the product category section you will see the following:
-     “NI-2974”.
+     NI-2974
 ==Technical Support and Community Knowledge Base==

@@ Line 6: / Line 6: @@
 * Getting Started Guide
 {|
-||[[File:USRP_2974_frt_dia.jpg|250px|center]]
+||[[File:USRP_2974_frt_dia.jpg|300px|center]]
 |}

@@ Line 8: / Line 8: @@
 ||[[File:USRP_2974_frt_dia.jpg|250px|center]]
 |}
 ==Verify the Contents of Your Kit==

@@ Line 132: / Line 132: @@
 ==Additional Resources==
-* [[NI_USRP-2974_Hardware_Resource_00 | USRP-2974 Hardware Resource]]
+* [[USRP-2974 | USRP-2974 Hardware Resource]]
 * http://www.ni.com/pdf/manuals/377416c.pdf
 [[Category:Getting Started Guides]]

@@ Line 57: / Line 57: @@
 * To test communications, ping the USRP FPGA at address "192.168.40.2" or “192.168.30.2”
-For more details on network setup, including PCIe connectivity, please see the section [[NI_USRP-2974_Hardware_Resource_0#Interfaces_and_Connectivity|Interfaces and Connectivity]] of the NI USRP-2974 Hardware Resources page.
+For more details on network setup, including PCIe connectivity, please see the section [[USRP-2974#Interfaces_and_Connectivity|Interfaces and Connectivity]] of the NI USRP-2974 Hardware Resources page.
 ==Test and Verify the Operation of the USRP==