Difference between revisions of "USRP X Series Quick Start (Daughterboard Installation)"

From Ettus Knowledge Base
Jump to: navigation, search
(UHD FFT)
Line 148: Line 148:
  
 
     $ uhd_fft
 
     $ uhd_fft
 
  
 
[figure 27]
 
[figure 27]

Revision as of 14:49, 19 April 2016

Introduction

Application Note Number: AN-5501

Authors: John Smith and Jane Smith

Last Modified Date: 2016/04/15

Reference: https://www.ettus.com/content/files/kb/xseries-quick-start.pdf

Overview

This Quick Start is meant to show you how to put together your new X300/310. We will start at the point when you have yet to unpack the boxes and go all the way to being able to ping the device, performing a quick software probe to verify hardware components and finally running a simple FFT demo. This Quick Start does not cover the installation of software on the host computer.

Tools Required

  • Philips Screwdriver
  • 5/16” wrench

Pre-installed Software

Box Contents

USRP Box

  • 1 x USRP X300/X310
  • 1 x SFP Adapter for 1 GigE
  • 1 x Power Supply and US Cord
  • 1 x USB 2.0 JTAG Debug Cable
  • 1 x Gigabit Ethernet Cable
  • 4 x SMA-Bulkhead Cables
  • 16 x Daughterboard Screws

Daughterboard Boxes

  • 2 x SBX Daughterboards

Antenna Boxes

  • One or more Antennas

[figure1]

[figure2]

Proper Handling

Daughterboard installation and component verification (Ettus Research recommends you perform the installation with no power to the USRP and using ESD equipment)

Installation Process

Step 1

Unscrew the 2 screws on the top of the USRP and remove cover. (Lift up about 15 degrees and wiggle back as there is a flange on the front part of the cover)

[figure 3]

[figure 4]

[figure 5]

Step 2

Line up the 8 screw holes on the Daughterboard with the USRP Motherboard standoffs (they only go one way).

[figure 6]

[figure 7]

Step 3

After you have aligned the Daughterboard correctly you can press the Daughterboard on to the connectors below them (you will feel them snap into place).

[figure 8]

[figure 9]

Step 4

Put 8 of the screws provided in the daughterboard

[figure 10]

Step 5

Repeat steps 2- 4 for the second Daughterboard

Step 6

It is recommended to connect the bulkhead cables one at a time to avoid confusion. The Daughterboards and front panel of the X300/310 are clearly labeled as to which cable goes where.

[figure 11]

[figure 12]

[figure 13]

[figure 14]

[figure 15]

[figure 16]

Step 7

Repeat step 6 for the other bulkhead cables

[figure 17]

[figure 18]

Step 8

Install USRP cover with screws

[figure 19]

Step 9

Connect the SFP 1 GigE adapter into USRP SFP port 0

[figure 20]

[figure 21]

Step 10

Connect the Gigabit Ethernet cable and power cord provided

[figure 22]

Step 11

Attach any Antennas you may have purchased

[figure 23]

Step 12

On the computer(host) you plan to use to connect to the USRP set the Ethernet adapter to have an IP address of 192.168.10.1 with a subnet mask of 255.255.255.0. Connect the other end of the Gigabit Ethernet cable to your computer.

[figure 24]

Step 13

Power on the USRP (button on the front right of the USRP)

Step 14

Ping the device from host computer:

   $ ping 192.168.10.2

[figure 25]

Step 15

Assuming you have properly installed the UHD driver (http://code.ettus.com/redmine/ettus/projects/uhd/wiki) you can now run this command in a terminal/command window: $ uhd_usrp_probe. This will tell you about the hardware inside of your USRP. The output will look like the following:

insert uhd_usrp_probe output

UHD FFT

Try the UHD_FFT demo that comes with GNU Radio

1. Connect one antenna to RX2 on the left Daughterboard (Daughterboard A)

[figure 26]

2.From the terminal/command window:

   $ uhd_fft

[figure 27]

[figure 28]