Difference between revisions of "USRP X Series Quick Start (Daughterboard Installation)"
Line 35: | Line 35: | ||
* One or more Antennas | * One or more Antennas | ||
− | [ | + | [[File:Xseries quickstart figure 1.png|700px|center]] |
− | [ | + | [[File:Xseries quickstart figure 2.png|700px|center]] |
==Proper Handling== | ==Proper Handling== | ||
Line 47: | Line 47: | ||
is a flange on the front part of the cover) | is a flange on the front part of the cover) | ||
− | [figure 3] | + | [[File:Xseries quickstart figure 3.png|700px|center]] |
− | [figure 4] | + | [[File:Xseries quickstart figure 4.png|700px|center]] |
− | [figure 5] | + | [[File:Xseries quickstart figure 5.png|700px|center]] |
===Step 2=== | ===Step 2=== | ||
Line up the 8 screw holes on the Daughterboard with the USRP Motherboard standoffs (they only go one way). | Line up the 8 screw holes on the Daughterboard with the USRP Motherboard standoffs (they only go one way). | ||
− | [figure 6] | + | [[File:Xseries quickstart figure 6.png|700px|center]] |
− | [figure 7] | + | [[File:Xseries quickstart figure 7.png|700px|center]] |
===Step 3=== | ===Step 3=== | ||
After you have aligned the Daughterboard correctly you can press the Daughterboard on to the connectors below them (you will feel them snap into place). | After you have aligned the Daughterboard correctly you can press the Daughterboard on to the connectors below them (you will feel them snap into place). | ||
− | [figure 8] | + | [[File:Xseries quickstart figure 8.png|700px|center]] |
− | [figure 9] | + | [[File:Xseries quickstart figure 9.png|700px|center]] |
===Step 4=== | ===Step 4=== | ||
Put 8 of the screws provided in the daughterboard | Put 8 of the screws provided in the daughterboard | ||
− | [figure 10] | + | [[File:Xseries quickstart figure 10.png|700px|center]] |
===Step 5=== | ===Step 5=== | ||
Line 79: | Line 79: | ||
panel of the X300/310 are clearly labeled as to which cable goes where. | panel of the X300/310 are clearly labeled as to which cable goes where. | ||
− | [figure 11] | + | [[File:Xseries quickstart figure 11.png|700px|center]] |
− | [figure 12] | + | [[File:Xseries quickstart figure 12.png|700px|center]] |
− | [figure 13] | + | [[File:Xseries quickstart figure 13.png|700px|center]] |
− | [figure 14] | + | [[File:Xseries quickstart figure 14.png|700px|center]] |
− | [figure 15] | + | [[File:Xseries quickstart figure 15.png|700px|center]] |
− | [figure 16] | + | [[File:Xseries quickstart figure 16.png|700px|center]] |
===Step 7=== | ===Step 7=== | ||
Repeat step 6 for the other bulkhead cables | Repeat step 6 for the other bulkhead cables | ||
− | [figure 17] | + | [[File:Xseries quickstart figure 17.png|700px|center]] |
− | [figure 18] | + | [[File:Xseries quickstart figure 18.png|700px|center]] |
===Step 8=== | ===Step 8=== | ||
Install USRP cover with screws | Install USRP cover with screws | ||
− | [figure 19] | + | [[File:Xseries quickstart figure 19.png|700px|center]] |
===Step 9=== | ===Step 9=== | ||
Connect the SFP 1 GigE adapter into USRP SFP port 0 | Connect the SFP 1 GigE adapter into USRP SFP port 0 | ||
− | [figure 20] | + | [[File:Xseries quickstart figure 20.png|700px|center]] |
− | [figure 21] | + | [[File:Xseries quickstart figure 21.png|700px|center]] |
===Step 10=== | ===Step 10=== | ||
Connect the Gigabit Ethernet cable and power cord provided | Connect the Gigabit Ethernet cable and power cord provided | ||
− | [figure 22] | + | [[File:Xseries quickstart figure 22.png|700px|center]] |
===Step 11=== | ===Step 11=== | ||
Attach any Antennas you may have purchased | Attach any Antennas you may have purchased | ||
− | [figure 23] | + | [[File:Xseries quickstart figure 23.png|700px|center]] |
===Step 12=== | ===Step 12=== | ||
On the computer(host) you plan to use to connect to the USRP set the Ethernet adapter to have an IP address of 192.168.10.1 with a subnet mask of 255.255.255.0. Connect the other end of the Gigabit Ethernet cable to your computer. | On the computer(host) you plan to use to connect to the USRP set the Ethernet adapter to have an IP address of 192.168.10.1 with a subnet mask of 255.255.255.0. Connect the other end of the Gigabit Ethernet cable to your computer. | ||
− | [figure 24] | + | [[File:Xseries quickstart figure 24.png|700px|center]] |
===Step 13=== | ===Step 13=== | ||
Line 133: | Line 133: | ||
$ ping 192.168.10.2 | $ ping 192.168.10.2 | ||
− | [figure 25] | + | [[File:Xseries quickstart figure 25.png|700px|center]] |
===Step 15=== | ===Step 15=== | ||
Line 145: | Line 145: | ||
1. Connect one antenna to RX2 on the left Daughterboard (Daughterboard A) | 1. Connect one antenna to RX2 on the left Daughterboard (Daughterboard A) | ||
− | [figure 26] | + | [[File:Xseries quickstart figure 26.png|700px|center]] |
2.From the terminal/command window: | 2.From the terminal/command window: | ||
Line 151: | Line 151: | ||
$ uhd_fft | $ uhd_fft | ||
− | [figure 27] | + | [[File:Xseries quickstart figure 27.png|700px|center]] |
− | [figure 28] | + | [[File:Xseries quickstart figure 28.png|700px|center]] |
Revision as of 11:43, 28 April 2016
Contents
Introduction
Application Note Number: AN-5501
Authors: John Smith and Jane Smith
Organization: Ettus Research
Last Modified Date: 2016/04/15
Reference: https://www.ettus.com/content/files/kb/xseries-quick-start.pdf
Overview
This Quick Start is meant to show you how to put together your new X300/310. We will start at the point when you have yet to unpack the boxes and go all the way to being able to ping the device, performing a quick software probe to verify hardware components and finally running a simple FFT demo. This Quick Start does not cover the installation of software on the host computer.
Tools Required
- Philips Screwdriver
- 5/16” wrench
Pre-installed Software
- UHD Latest (http://code.ettus.com/redmine/ettus/projects/uhd/wiki)
- GNU Radio (http://gnuradio.org/redmine/projects/gnuradio/wiki/InstallingGR)
Box Contents
USRP Box
- 1 x USRP X300/X310
- 1 x SFP Adapter for 1 GigE
- 1 x Power Supply and US Cord
- 1 x USB 2.0 JTAG Debug Cable
- 1 x Gigabit Ethernet Cable
- 4 x SMA-Bulkhead Cables
- 16 x Daughterboard Screws
Daughterboard Boxes
- 2 x SBX Daughterboards
Antenna Boxes
- One or more Antennas
Proper Handling
Ettus Research recommends you perform the installation with no power to the USRP and using ESD equipment.
Installation Process
Step 1
Unscrew the 2 screws on the top of the USRP and remove cover. (Lift up about 15 degrees and wiggle back as there is a flange on the front part of the cover)
Step 2
Line up the 8 screw holes on the Daughterboard with the USRP Motherboard standoffs (they only go one way).
Step 3
After you have aligned the Daughterboard correctly you can press the Daughterboard on to the connectors below them (you will feel them snap into place).
Step 4
Put 8 of the screws provided in the daughterboard
Step 5
Repeat steps 2- 4 for the second Daughterboard
Step 6
It is recommended to connect the bulkhead cables one at a time to avoid confusion. The Daughterboards and front panel of the X300/310 are clearly labeled as to which cable goes where.
Step 7
Repeat step 6 for the other bulkhead cables
Step 8
Install USRP cover with screws
Step 9
Connect the SFP 1 GigE adapter into USRP SFP port 0
Step 10
Connect the Gigabit Ethernet cable and power cord provided
Step 11
Attach any Antennas you may have purchased
Step 12
On the computer(host) you plan to use to connect to the USRP set the Ethernet adapter to have an IP address of 192.168.10.1 with a subnet mask of 255.255.255.0. Connect the other end of the Gigabit Ethernet cable to your computer.
Step 13
Power on the USRP (button on the front right of the USRP)
Step 14
Ping the device from host computer:
$ ping 192.168.10.2
Step 15
Assuming you have properly installed the UHD driver (http://code.ettus.com/redmine/ettus/projects/uhd/wiki) you can now run this command in a terminal/command window: $ uhd_usrp_probe. This will tell you about the hardware inside of your USRP. The output will look like the following:
insert uhd_usrp_probe output
UHD FFT
Try the UHD_FFT demo that comes with GNU Radio
1. Connect one antenna to RX2 on the left Daughterboard (Daughterboard A)
2.From the terminal/command window:
$ uhd_fft