Difference between revisions of "CBX"

From Ettus Knowledge Base
Jump to: navigation, search
m (→‎Device Overview: add supported by UHD sentence)
 
(32 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
== Device Overview ==
 
== Device Overview ==
−
The CBX is a full-duplex, wideband transceiver that covers a frequency band from 1.2 GHz to 6 GHz with a instantaneous bandwidth of 40 MHz or 120 MHz. The CBX can serve a wide variety of application areas, including WiFi research, cellular base stations, cognitive radio research, and RADAR.
+
The CBX is a full-duplex, wideband transceiver that covers a frequency band from 1.2 GHz to 6 GHz with a instantaneous bandwidth of 40 MHz or 120 MHz. The CBX can serve a wide variety of application areas, including WiFi research, cellular base stations, cognitive radio research, and RADAR. The CBX daughterboard is supported by the USRP Hardware Driver™ (UHD) software API for seamless integration into existing applications.
  
 
The CBX does not provided phase coherent operation, and therefore is not recommended for MIMO and Phased Array applications.
 
The CBX does not provided phase coherent operation, and therefore is not recommended for MIMO and Phased Array applications.
  
 
== Key Features==
 
== Key Features==
−
 
+
{|
−
==RF Specifications==
+
|style="vertical-align:top"|
 
* Frequency Range: 1.2GHz - 6GHz
 
* Frequency Range: 1.2GHz - 6GHz
 
* Versions: 40MHz / 120MHz
 
* Versions: 40MHz / 120MHz
 +
|[[File:Product cbx 40.jpg|250px|center]]
 +
|[[File:Product cbx 120.jpg|250px|center]]
 +
|}
  
−
==Physical Specifications==
+
==Daughterboard Specifications==
−
Lorem ipsum dolor sit amet, consectetur adipisicing elit. Quod voluptates molestias excepturi nisi ea minus hic iste velit optio doloremque similique ab nulla, beatae obcaecati! Nobis, at dolorum id nostrum
+
===Features===
 +
* 2 quadrature frontends (1 transmit, 1 receive)
 +
** Defaults to direct conversion
 +
** Can be used in low IF mode through lo_offset with uhd::tune_request_t
 +
* Independent receive and transmit LO's and synthesizers
 +
** Allows for full-duplex operation on different transmit and receive frequencies
 +
** Can be set to use Integer-N tuning for better spur performance with uhd::tune_request_t
 +
 
 +
===Antennas===
 +
Transmit: '''TX/RX'''
 +
 
 +
Receive: '''TX/RX''' or '''RX2'''
 +
* '''Frontend 0:''' Complex baseband signal for selected antenna
 +
* '''Note:''' The user may set the receive antenna to be TX/RX or RX2. However, when using a CBX board in full-duplex mode, the receive antenna will always be set to RX2, regardless of the settings.
 +
 
 +
===Gains===
 +
* Transmit Gains: '''PGA0''', Range: 0-31.5dB
 +
* Receive Gains: '''PGA0''', Range: 0-31.5dB
 +
 
 +
===Bandwidths===
 +
* CBX: 40 MHz, RX & TX
 +
* CBX-120: 120 MHz, RX & TX
 +
 
 +
===Sensors===
 +
* '''lo_locked:''' boolean for LO lock state
 +
 
 +
===LEDs===
 +
* All LEDs flash when daughterboard control is initialized
 +
* '''TX LD''': Transmit Synthesizer Lock Detect
 +
* '''TX/RX''': Receiver on TX/RX antenna port (No TX)
 +
* '''RX LD''': Receive Synthesizer Lock Detect
 +
* '''RX1/RX2''': Receiver on RX2 antenna port
 +
 
 +
==RF Specifications==
 +
===Freq Range===
 +
* 1.2GHz - 6GHz
 +
 
 +
===Noise Figure===
 +
* 5 - 7.5 dB @ (1.2GHz ~ 5GHz)
 +
* 7.5dB  - 10 dB (5GHz ~ 6GHz)
 +
 
 +
===RX IIP3 (Max)===
 +
* 8 - 10 dBm
 +
 
 +
===RX IQ Imbalance===
 +
* -20 dBc
 +
 
 +
===TX Power (Max)===
 +
* 22 dBm @ (1.2GHz ~ 3GHz)
 +
* 12 ~ 22 dBm @ (3GHz ~ 6GHz)
 +
 
 +
===TX OIP3===
 +
* 30 - 32 dBm @ (1.2GHz ~ 5GHz)
 +
* 26 ~ 30 dBm @ (5GHz ~ 6GHz)
 +
 
 +
===TX IQ Imbalance===
 +
* -20 dBc
 +
 
 +
===Input/Output Impedance===
 +
* All RF Ports are matched to 50 Ohm with -10dB or better return loss generally. Detailed test is pending.
 +
 
 +
===Input Power Levels===
 +
* The maximum input power for the CBX is -15 dBm.
 +
 
 +
==RF Performance Data==
 +
* [http://files.ettus.com/performance_data/cbx/CBX-without-UHD-corrections.pdf CBX without UHD Corrections]
 +
 
 +
==Hardware Specifications==
 +
* Ettus Research recommends to always use the latest stable version of UHD
 +
 
 +
===CBX===
 +
* Current Hardware Revision: 1
 +
* Minimum version of UHD required: 3.8.0
  
 
==Environmental Specifications==
 
==Environmental Specifications==
 
===Operating Temperature Range===
 
===Operating Temperature Range===
 
* 0-40 °C
 
* 0-40 °C
 +
 +
===Operating Humidity Range===
 +
* 10% to 90% non-condensing
  
 
==USRP Compatibility==
 
==USRP Compatibility==
Line 23: Line 101:
 
===CBX-120===
 
===CBX-120===
 
* X Series only
 
* X Series only
 +
 +
==Phase Synchronization==
 +
The CBX daughterboard is not capable of phase-synchronous operation. The SBX, UBX, TwinRX daughterboards are recommended for phase-coherent applications.
  
 
==Schematics==
 
==Schematics==
Line 28: Line 109:
 
[http://files.ettus.com/schematics/cbx/CBX.pdf CBX Schematics]
 
[http://files.ettus.com/schematics/cbx/CBX.pdf CBX Schematics]
  
−
==Datasheets==
+
==Key Component Datasheets==
−
[http://www.avagotech.com/docs/AV02-2919EN VMMK-3603]
+
{| class="wikitable" style="width:80%"
 +
!Part Number
 +
!Description
 +
!Schematic ID (Page)
 +
|-
 +
|[http://www.avagotech.com/docs/AV02-2919EN VMMK-3603]
 +
|Low Noise Amplifier
 +
|U1, U5 (1)
 +
|-
  
−
[http://www.skyworksinc.com/uploads/documents/AS225_313LF_200148E.pdf AS225-313LF]
+
|[http://www.skyworksinc.com/uploads/documents/AS225_313LF_200148E.pdf AS225-313LF]
 +
|SPDT Switch
 +
|U3, U6 (1)
 +
|-
  
−
[http://media.digikey.com/pdf/Data%20Sheets/Analog%20Devices%20PDFs/HMC624LP4E.pdf HMC624LP4E]
+
|[http://media.digikey.com/pdf/Data%20Sheets/Analog%20Devices%20PDFs/HMC624LP4E.pdf HMC624LP4E]
 +
|ATTENUATOR
 +
|U7, U2 (1)
 +
|-
  
−
[http://www.avagotech.com/docs/AV02-1985EN MGA82563]
+
|[http://www.avagotech.com/docs/AV02-1985EN MGA82563]
 +
|Amplifier
 +
|U4 (1)
 +
|-
  
−
[https://www.minicircuits.com/pdfs/GVA-84+.pdf GVA-84+]
+
|[https://www.minicircuits.com/pdfs/GVA-84+.pdf GVA-84+]
 +
|Amplifier
 +
|U9 (1)
 +
|-
  
−
[https://www.minicircuits.com/pdfs/PHA-1+.pdf PHA-1+]
+
|[https://www.minicircuits.com/pdfs/PHA-1+.pdf PHA-1+]
 +
|Amplifier
 +
|U8 (1)
 +
|-
  
−
[http://www.analog.com/media/en/technical-documentation/data-sheets/ADL5380.pdf ADL5380ACPZ]
+
|[http://www.analog.com/media/en/technical-documentation/data-sheets/ADL5380.pdf ADL5380ACPZ]
 +
|Quadrature Demodulator
 +
|U11 (2)
 +
|-
  
−
[http://www.analog.com/media/en/technical-documentation/data-sheets/ADA4927-1_ADA4927-2.pdf ADA4927-2YCPZ]
+
|[http://www.analog.com/media/en/technical-documentation/data-sheets/ADA4927-1_ADA4927-2.pdf ADA4927-2YCPZ]
 +
|Differential ADC Driver
 +
|U10 (2)
 +
|-
  
−
[http://www.analog.com/media/en/technical-documentation/data-sheets/AD8591_8592_8594.pdf AD8591ARTZ-REEL]
+
|[http://www.analog.com/media/en/technical-documentation/data-sheets/AD8591_8592_8594.pdf AD8591ARTZ-REEL]
 +
|Amplifiers
 +
|U31 (2)
 +
|-
  
−
[https://www.fairchildsemi.com/datasheets/NC/NC7WZ04.pdf NC7WZ04P6X]
+
|[https://www.fairchildsemi.com/datasheets/NC/NC7WZ04.pdf NC7WZ04P6X]
 +
|Dual Inverter
 +
|U26 (3); U15, U16 (4); U21 (5); U27 (6)
 +
|-
  
−
[https://datasheets.maximintegrated.com/en/ds/MAX2870.pdf MAX2870ETJ+]
+
|[https://datasheets.maximintegrated.com/en/ds/MAX2870.pdf MAX2870ETJ+]
 +
|Fractional/Integer-N Synthesizer
 +
|U23 (3); U24 (6)
 +
|-
  
−
[http://www.skyworksinc.com/uploads/documents/200027E.pdf SKY13267-321]
+
|[http://www.skyworksinc.com/uploads/documents/200027E.pdf SKY13267-321]
 +
|Diversity Switch
 +
|U12 (3); U25 (6)
 +
|-
  
−
[https://www.minicircuits.com/pdfs/LFCN-2000.pdf LFCN-2000+]
+
|[https://www.minicircuits.com/pdfs/LFCN-2000.pdf LFCN-2000+]
 +
|Low Pass Filter
 +
|FL13 (3); FL12 (6)
 +
|-
  
−
[http://www.ti.com/lit/ds/symlink/lp3878-adj.pdf LP3878MR-ADJ]
+
|[http://www.ti.com/lit/ds/symlink/lp3878-adj.pdf LP3878MR-ADJ]
 +
|Voltage Regulator
 +
|U13, U14 (4); U19, U20 (5)
 +
|-
  
−
[http://ww1.microchip.com/downloads/en/DeviceDoc/21210G.pdf 24LC024]
+
|[http://ww1.microchip.com/downloads/en/DeviceDoc/21210G.pdf 24LC024]
 +
|EEPROM
 +
|U17 (4); U22 (5)
 +
|-
  
−
[http://www.analog.com/media/en/technical-documentation/evaluation-documentation/ADL5375.pdf ADL5375-05]
+
|[http://www.analog.com/media/en/technical-documentation/evaluation-documentation/ADL5375.pdf ADL5375-05]
 +
|Quadrature Modulator
 +
|U18 (5)
 +
|-
 +
|}
  
−
==Mechanical Info (size, weight, drawings)==
+
==Drawings==
−
Lorem ipsum dolor sit amet, consectetur adipisicing elit. Quod voluptates molestias excepturi nisi ea minus hic iste velit optio doloremque similique ab nulla, beatae obcaecati! Nobis, at dolorum id nostrum? Lorem ipsum dolor sit amet, consectetur adipisicing elit. Quod voluptates molestias excepturi nisi ea minus hic iste velit optio doloremque similique ab nulla, beatae obcaecati! Nobis, at dolorum id nostrum
+
* [[File:cu ettus-cca-cbx.pdf]]
  
−
==Interfaces and Connectivity==
+
==RF Connectors==
−
Lorem ipsum dolor sit amet, consectetur adipisicing elit. Quod voluptates molestias excepturi nisi ea minus hic iste velit optio doloremque similique ab nulla, beatae obcaecati! Nobis, at dolorum id nostrum Lorem ipsum dolor sit amet, consectetur adipisicing elit. Quod voluptates molestias excepturi nisi ea minus hic iste velit optio doloremque similique ab nulla, beatae obcaecati! Nobis, at dolorum id nostrum Lorem ipsum dolor sit amet, consectetur adipisicing elit. Quod voluptates molestias excepturi nisi ea minus hic iste velit optio doloremque similique ab nulla, beatae obcaecati! Nobis, at dolorum id nostrum
+
* The CBX daughterboard features female SMA connectors for both the TX/RX and RX2 connectors.
  
 
==Certifications==
 
==Certifications==
Line 71: Line 206:
 
As of December 1st, 2010 all Ettus Research products are RoHS compliant unless otherwise noted. More information can be found at [http://ettus.com/legal/rohs-information http://ettus.com/legal/rohs-information]
 
As of December 1st, 2010 all Ettus Research products are RoHS compliant unless otherwise noted. More information can be found at [http://ettus.com/legal/rohs-information http://ettus.com/legal/rohs-information]
  
 +
===China RoHS===
 +
'''Management Methods for Controlling Pollution Caused by Electronic Information Products Regulation'''
  
−
==Certificate of Volatility==
+
'''Chinese Customers'''
−
* CBX
+
  
−
==Performance Data==
+
National Instruments is in compliance with the Chinese policy on the Restriction of Hazardous Substances (RoHS) used in Electronic Information Products. For more information about the National Instruments China RoHS compliance, visit [http://www.ni.com/environment/rohs_china ni.com/environment/rohs_china].
−
* [http://files.ettus.com/performance_data/cbx/CBX-without-UHD-corrections.pdf CBX without UHD Corrections]
+
 
 +
==Certificate of Volatility==
 +
===CBX-40/CBX-120===
 +
* [[Media:volatility UBX CBX WBX SBX r1 1.pdf]]
  
 
==Downloads==
 
==Downloads==

Latest revision as of 12:56, 13 November 2019

Device Overview

The CBX is a full-duplex, wideband transceiver that covers a frequency band from 1.2 GHz to 6 GHz with a instantaneous bandwidth of 40 MHz or 120 MHz. The CBX can serve a wide variety of application areas, including WiFi research, cellular base stations, cognitive radio research, and RADAR. The CBX daughterboard is supported by the USRP Hardware Driver™ (UHD) software API for seamless integration into existing applications.

The CBX does not provided phase coherent operation, and therefore is not recommended for MIMO and Phased Array applications.

Key Features

  • Frequency Range: 1.2GHz - 6GHz
  • Versions: 40MHz / 120MHz
Product cbx 40.jpg
Product cbx 120.jpg

Daughterboard Specifications

Features

  • 2 quadrature frontends (1 transmit, 1 receive)
    • Defaults to direct conversion
    • Can be used in low IF mode through lo_offset with uhd::tune_request_t
  • Independent receive and transmit LO's and synthesizers
    • Allows for full-duplex operation on different transmit and receive frequencies
    • Can be set to use Integer-N tuning for better spur performance with uhd::tune_request_t

Antennas

Transmit: TX/RX

Receive: TX/RX or RX2

  • Frontend 0: Complex baseband signal for selected antenna
  • Note: The user may set the receive antenna to be TX/RX or RX2. However, when using a CBX board in full-duplex mode, the receive antenna will always be set to RX2, regardless of the settings.

Gains

  • Transmit Gains: PGA0, Range: 0-31.5dB
  • Receive Gains: PGA0, Range: 0-31.5dB

Bandwidths

  • CBX: 40 MHz, RX & TX
  • CBX-120: 120 MHz, RX & TX

Sensors

  • lo_locked: boolean for LO lock state

LEDs

  • All LEDs flash when daughterboard control is initialized
  • TX LD: Transmit Synthesizer Lock Detect
  • TX/RX: Receiver on TX/RX antenna port (No TX)
  • RX LD: Receive Synthesizer Lock Detect
  • RX1/RX2: Receiver on RX2 antenna port

RF Specifications

Freq Range

  • 1.2GHz - 6GHz

Noise Figure

  • 5 - 7.5 dB @ (1.2GHz ~ 5GHz)
  • 7.5dB - 10 dB (5GHz ~ 6GHz)

RX IIP3 (Max)

  • 8 - 10 dBm

RX IQ Imbalance

  • -20 dBc

TX Power (Max)

  • 22 dBm @ (1.2GHz ~ 3GHz)
  • 12 ~ 22 dBm @ (3GHz ~ 6GHz)

TX OIP3

  • 30 - 32 dBm @ (1.2GHz ~ 5GHz)
  • 26 ~ 30 dBm @ (5GHz ~ 6GHz)

TX IQ Imbalance

  • -20 dBc

Input/Output Impedance

  • All RF Ports are matched to 50 Ohm with -10dB or better return loss generally. Detailed test is pending.

Input Power Levels

  • The maximum input power for the CBX is -15 dBm.

RF Performance Data

Hardware Specifications

  • Ettus Research recommends to always use the latest stable version of UHD

CBX

  • Current Hardware Revision: 1
  • Minimum version of UHD required: 3.8.0

Environmental Specifications

Operating Temperature Range

  • 0-40 °C

Operating Humidity Range

  • 10% to 90% non-condensing

USRP Compatibility

CBX-40

  • N or X Series

CBX-120

  • X Series only

Phase Synchronization

The CBX daughterboard is not capable of phase-synchronous operation. The SBX, UBX, TwinRX daughterboards are recommended for phase-coherent applications.

Schematics

CBX

CBX Schematics

Key Component Datasheets

Part Number Description Schematic ID (Page)
VMMK-3603 Low Noise Amplifier U1, U5 (1)
AS225-313LF SPDT Switch U3, U6 (1)
HMC624LP4E ATTENUATOR U7, U2 (1)
MGA82563 Amplifier U4 (1)
GVA-84+ Amplifier U9 (1)
PHA-1+ Amplifier U8 (1)
ADL5380ACPZ Quadrature Demodulator U11 (2)
ADA4927-2YCPZ Differential ADC Driver U10 (2)
AD8591ARTZ-REEL Amplifiers U31 (2)
NC7WZ04P6X Dual Inverter U26 (3); U15, U16 (4); U21 (5); U27 (6)
MAX2870ETJ+ Fractional/Integer-N Synthesizer U23 (3); U24 (6)
SKY13267-321 Diversity Switch U12 (3); U25 (6)
LFCN-2000+ Low Pass Filter FL13 (3); FL12 (6)
LP3878MR-ADJ Voltage Regulator U13, U14 (4); U19, U20 (5)
24LC024 EEPROM U17 (4); U22 (5)
ADL5375-05 Quadrature Modulator U18 (5)

Drawings

RF Connectors

  • The CBX daughterboard features female SMA connectors for both the TX/RX and RX2 connectors.

Certifications

RoHS

As of December 1st, 2010 all Ettus Research products are RoHS compliant unless otherwise noted. More information can be found at http://ettus.com/legal/rohs-information

China RoHS

Management Methods for Controlling Pollution Caused by Electronic Information Products Regulation

Chinese Customers

National Instruments is in compliance with the Chinese policy on the Restriction of Hazardous Substances (RoHS) used in Electronic Information Products. For more information about the National Instruments China RoHS compliance, visit ni.com/environment/rohs_china.

Certificate of Volatility

CBX-40/CBX-120

Downloads

FPGA Resources

UHD Stable Binaries

UHD Source Code on Github

Retrieved from "https://kb.ettus.com/index.php?title=CBX&oldid=4403"