Difference between revisions of "USRP X Series Quick Start (Daughterboard Installation)"
Line 7: | Line 7: | ||
Reference: https://www.ettus.com/content/files/kb/xseries-quick-start.pdf | Reference: https://www.ettus.com/content/files/kb/xseries-quick-start.pdf | ||
+ | |||
+ | ==Overview== | ||
+ | This Quick Start is meant to show you how to put together your new X300/310. We will start at the point when you have yet to unpack the boxes and go all the way to being able to ping the device, performing a quick software probe to verify hardware components and finally running a simple FFT demo. This Quick Start does not cover the installation of software on the host computer. | ||
+ | |||
+ | ==Tools Required== | ||
+ | * Philips Screwdriver | ||
+ | * 5/16” wrench | ||
+ | |||
+ | ==Pre-installed Software== | ||
+ | * UHD Latest (http://code.ettus.com/redmine/ettus/projects/uhd/wiki) | ||
+ | * GNU Radio (http://gnuradio.org/redmine/projects/gnuradio/wiki/InstallingGR) | ||
+ | |||
+ | ==Box Contents== | ||
+ | ===USRP Box=== | ||
+ | * 1 x USRP X300/X310 | ||
+ | * 1 x SFP Adapter for 1 GigE | ||
+ | * 1 x Power Supply and US Cord | ||
+ | * 1 x USB 2.0 JTAG Debug Cable | ||
+ | * 1 x Gigabit Ethernet Cable | ||
+ | * 4 x SMA-Bulkhead Cables | ||
+ | * 16 x Daughterboard Screws | ||
+ | ===Daughterboard Boxes=== | ||
+ | * 2 x SBX Daughterboards | ||
+ | ===Antenna Boxes=== | ||
+ | * One or more Antennas | ||
+ | |||
+ | [figure1] | ||
+ | |||
+ | [figure2] | ||
+ | |||
+ | ==Proper Handling== | ||
+ | Daughterboard installation and component verification (Ettus Research recommends you perform the installation with no power to the USRP and using ESD equipment) | ||
+ | |||
+ | ==Step 1== | ||
+ | Unscrew the 2 screws on the top of the USRP and remove cover. (Lift up about 15 degrees and wiggle back as there | ||
+ | is a flange on the front part of the cover) | ||
+ | |||
+ | [figure 3] | ||
+ | |||
+ | [figure 4] | ||
+ | |||
+ | [figure 5] | ||
+ | |||
+ | ==Step 2== | ||
+ | Line up the 8 screw holes on the Daughterboard with the USRP Motherboard standoffs (they only go one way). | ||
+ | |||
+ | [figure 6] | ||
+ | |||
+ | [figure 7] | ||
+ | |||
+ | ==Step 3== | ||
+ | After you have aligned the Daughterboard correctly you can press the Daughterboard on to the connectors below them (you will feel them snap into place). | ||
+ | |||
+ | [figure 8] | ||
+ | |||
+ | [figure 9] | ||
+ | |||
+ | ==Step 4== | ||
+ | Put 8 of the screws provided in the daughterboard | ||
+ | |||
+ | [figure 10] | ||
+ | |||
+ | ==Step 5== | ||
+ | Repeat steps 2- 4 for the second Daughterboard | ||
+ | |||
+ | ==Step 6== | ||
+ | It is recommended to connect the bulkhead cables one at a time to avoid confusion. The Daughterboards and front | ||
+ | panel of the X300/310 are clearly labeled as to which cable goes where. | ||
+ | |||
+ | [figure 11] | ||
+ | |||
+ | [figure 12] | ||
+ | |||
+ | [figure 13] | ||
+ | |||
+ | [figure 14] | ||
+ | |||
+ | [figure 15] | ||
+ | |||
+ | [figure 16] | ||
+ | |||
+ | ==Step 7== | ||
+ | Repeat step 6 for the other bulkhead cables | ||
+ | |||
+ | [figure 17] | ||
+ | |||
+ | [figure 18] | ||
+ | |||
+ | ==Step 8== | ||
+ | Install USRP cover with screws | ||
+ | |||
+ | [figure 19] | ||
+ | |||
+ | ==Step 9== | ||
+ | Connect the SFP 1 GigE adapter into USRP SFP port 0 | ||
+ | |||
+ | [figure 20] | ||
+ | |||
+ | [figure 21] | ||
+ | |||
+ | ==Step 10== | ||
+ | Connect the Gigabit Ethernet cable and power cord provided | ||
+ | |||
+ | [figure 22] | ||
+ | |||
+ | ==Step 11== | ||
+ | Attach any Antennas you may have purchased | ||
+ | |||
+ | [figure 23] | ||
+ | |||
+ | ==Step 12== | ||
+ | On the computer(host) you plan to use to connect to the USRP set the Ethernet adapter to have an IP address of 192.168.10.1 with a subnet mask of 255.255.255.0. Connect the other end of the Gigabit Ethernet cable to your computer. | ||
+ | |||
+ | [figure 24] | ||
+ | |||
+ | ==Step 13== | ||
+ | Power on the USRP (button on the front right of the USRP) | ||
+ | |||
+ | ==Step 14== | ||
+ | Ping the device from host computer: | ||
+ | |||
+ | $ ping 192.168.10.2 | ||
+ | |||
+ | [figure 25] | ||
+ | |||
+ | ==Step 15== | ||
+ | Assuming you have properly installed the UHD driver (http://code.ettus.com/redmine/ettus/projects/uhd/wiki) you can now run this command in a terminal/command window: $ uhd_usrp_probe. This will tell you about the hardware inside of your USRP. The output will look like the following: | ||
+ | |||
+ | <code>insert uhd_usrp_probe output</code> | ||
+ | |||
+ | ==Step 16== | ||
+ | Try the UHD_FFT demo that comes with GNU Radio | ||
+ | |||
+ | 1. Connect one antenna to RX2 on the left Daughterboard (Daughterboard A) | ||
+ | |||
+ | [figure 26] | ||
+ | |||
+ | 2.From the terminal/command window: | ||
+ | |||
+ | $ uhd_fft | ||
+ | |||
+ | |||
+ | [figure 27] | ||
+ | |||
+ | [figure 28] | ||
Revision as of 15:46, 19 April 2016
Contents
Introduction
Application Note Number: AN-5501
Authors: John Smith and Jane Smith
Last Modified Date: 2016/04/15
Reference: https://www.ettus.com/content/files/kb/xseries-quick-start.pdf
Overview
This Quick Start is meant to show you how to put together your new X300/310. We will start at the point when you have yet to unpack the boxes and go all the way to being able to ping the device, performing a quick software probe to verify hardware components and finally running a simple FFT demo. This Quick Start does not cover the installation of software on the host computer.
Tools Required
- Philips Screwdriver
- 5/16” wrench
Pre-installed Software
- UHD Latest (http://code.ettus.com/redmine/ettus/projects/uhd/wiki)
- GNU Radio (http://gnuradio.org/redmine/projects/gnuradio/wiki/InstallingGR)
Box Contents
USRP Box
- 1 x USRP X300/X310
- 1 x SFP Adapter for 1 GigE
- 1 x Power Supply and US Cord
- 1 x USB 2.0 JTAG Debug Cable
- 1 x Gigabit Ethernet Cable
- 4 x SMA-Bulkhead Cables
- 16 x Daughterboard Screws
Daughterboard Boxes
- 2 x SBX Daughterboards
Antenna Boxes
- One or more Antennas
[figure1]
[figure2]
Proper Handling
Daughterboard installation and component verification (Ettus Research recommends you perform the installation with no power to the USRP and using ESD equipment)
Step 1
Unscrew the 2 screws on the top of the USRP and remove cover. (Lift up about 15 degrees and wiggle back as there is a flange on the front part of the cover)
[figure 3]
[figure 4]
[figure 5]
Step 2
Line up the 8 screw holes on the Daughterboard with the USRP Motherboard standoffs (they only go one way).
[figure 6]
[figure 7]
Step 3
After you have aligned the Daughterboard correctly you can press the Daughterboard on to the connectors below them (you will feel them snap into place).
[figure 8]
[figure 9]
Step 4
Put 8 of the screws provided in the daughterboard
[figure 10]
Step 5
Repeat steps 2- 4 for the second Daughterboard
Step 6
It is recommended to connect the bulkhead cables one at a time to avoid confusion. The Daughterboards and front panel of the X300/310 are clearly labeled as to which cable goes where.
[figure 11]
[figure 12]
[figure 13]
[figure 14]
[figure 15]
[figure 16]
Step 7
Repeat step 6 for the other bulkhead cables
[figure 17]
[figure 18]
Step 8
Install USRP cover with screws
[figure 19]
Step 9
Connect the SFP 1 GigE adapter into USRP SFP port 0
[figure 20]
[figure 21]
Step 10
Connect the Gigabit Ethernet cable and power cord provided
[figure 22]
Step 11
Attach any Antennas you may have purchased
[figure 23]
Step 12
On the computer(host) you plan to use to connect to the USRP set the Ethernet adapter to have an IP address of 192.168.10.1 with a subnet mask of 255.255.255.0. Connect the other end of the Gigabit Ethernet cable to your computer.
[figure 24]
Step 13
Power on the USRP (button on the front right of the USRP)
Step 14
Ping the device from host computer:
$ ping 192.168.10.2
[figure 25]
Step 15
Assuming you have properly installed the UHD driver (http://code.ettus.com/redmine/ettus/projects/uhd/wiki) you can now run this command in a terminal/command window: $ uhd_usrp_probe. This will tell you about the hardware inside of your USRP. The output will look like the following:
insert uhd_usrp_probe output
Step 16
Try the UHD_FFT demo that comes with GNU Radio
1. Connect one antenna to RX2 on the left Daughterboard (Daughterboard A)
[figure 26]
2.From the terminal/command window:
$ uhd_fft
[figure 27]
[figure 28]