USRP X Series Quick Start (Daughterboard Installation)

From Ettus Knowledge Base
Revision as of 23:45, 17 May 2016 by Ettus (Talk | contribs)

Jump to: navigation, search

Application Note Number

AN-904

Revision History

Date Author Details
2016-05-01 Neel Pandeya
Nate Temple 		Initial creation

Abstract

This application note is a detailed step-by-step guide to install a daughterboard into the USRP X300/X310.

Overview

This Quick Start is meant to show you how to put together your new X300/310. We will start at the point when you have yet to unpack the boxes and go all the way to being able to ping the device, performing a quick software probe to verify hardware components and finally running a simple FFT demo. This Quick Start does not cover the installation of software on the host computer.

Tools Required

  • Philips Screwdriver
  • 5/16” wrench

Pre-installed Software

Box Contents

USRP Box

  • 1 x USRP X300/X310
  • 1 x SFP Adapter for 1 GigE
  • 1 x Power Supply and US Cord
  • 1 x USB 2.0 JTAG Debug Cable
  • 1 x Gigabit Ethernet Cable
  • 4 x SMA-Bulkhead Cables
  • 16 x Daughterboard Screws

Daughterboard Boxes

  • 2 x SBX Daughterboards

Antenna Boxes

  • One or more Antennas
Xseries quickstart figure 1.png
Xseries quickstart figure 2.png

Proper Handling

Ettus Research recommends you perform the installation with no power to the USRP and using ESD equipment.

Installation Process

Step 1

Unscrew the 2 screws on the top of the USRP and remove cover. (Lift up about 15 degrees and wiggle back as there is a flange on the front part of the cover)

Xseries quickstart figure 3.png
Xseries quickstart figure 4.png
Xseries quickstart figure 5.png

Step 2

Line up the 8 screw holes on the Daughterboard with the USRP Motherboard standoffs (they only go one way).

Xseries quickstart figure 6.png
Xseries quickstart figure 7.png

Step 3

After you have aligned the Daughterboard correctly you can press the Daughterboard on to the connectors below them (you will feel them snap into place).

Xseries quickstart figure 8.png
Xseries quickstart figure 9.png

Step 4

Put 8 of the screws provided in the daughterboard

Xseries quickstart figure 10.png

Step 5

Repeat steps 2- 4 for the second Daughterboard

Step 6

It is recommended to connect the bulkhead cables one at a time to avoid confusion. The Daughterboards and front panel of the X300/310 are clearly labeled as to which cable goes where.

Xseries quickstart figure 11.png
Xseries quickstart figure 12.png
Xseries quickstart figure 13.png
Xseries quickstart figure 14.png
Xseries quickstart figure 15.png
Xseries quickstart figure 16.png

Step 7

Repeat step 6 for the other bulkhead cables

Xseries quickstart figure 17.png
Xseries quickstart figure 18.png

Step 8

Install USRP cover with screws

Xseries quickstart figure 19.png

Step 9

Connect the SFP 1 GigE adapter into USRP SFP port 0

Xseries quickstart figure 20.png
Xseries quickstart figure 21.png

Step 10

Connect the Gigabit Ethernet cable and power cord provided

Xseries quickstart figure 22.png

Step 11

Attach any Antennas you may have purchased

Xseries quickstart figure 23.png

Step 12

On the computer(host) you plan to use to connect to the USRP set the Ethernet adapter to have an IP address of 192.168.10.1 with a subnet mask of 255.255.255.0. Connect the other end of the Gigabit Ethernet cable to your computer.

Xseries quickstart figure 24.png

Step 13

Power on the USRP (button on the front right of the USRP)

Step 14

Ping the device from host computer: 

   $ ping 192.168.10.2
Xseries quickstart figure 25.png

Step 15

Assuming you have properly installed the UHD driver (http://code.ettus.com/redmine/ettus/projects/uhd/wiki) you can now run this command in a terminal/command window: $ uhd_usrp_probe. This will tell you about the hardware inside of your USRP. The output will look like the following: 

   $ uhd_usrp_probe 
   linux; GNU C++ version 4.8.4; Boost_105400; UHD_003.010.git-202-g9e0861e1
   
   -- X300 initialization sequence...
   -- Determining maximum frame size... 1472 bytes.
   -- Setup basic communication...
   -- Loading values from EEPROM...
   -- Setup RF frontend clocking...
   -- Radio 1x clock:200
   -- Detecting internal GPSDO.... No GPSDO found
   -- Initialize Radio0 control...
   -- Performing register loopback test... pass
   -- Initialize Radio1 control...
   -- Performing register loopback test... pass
     _____________________________________________________
    /
   |       Device: X-Series Device
   |     _____________________________________________________
   |    /
   |   |       Mboard: X300
   |   |   revision: 7
   |   |   revision_compat: 7
   |   |   product: 30518
   |   |   mac-addr0: ff:ff:ff:ff:ff:ff
   |   |   mac-addr1: ff:ff:ff:ff:ff:ff
   |   |   gateway: 255.255.255.255
   |   |   ip-addr0: 255.255.255.255
   |   |   subnet0: 255.255.255.255
   |   |   ip-addr1: 255.255.255.255
   |   |   subnet1: 255.255.255.255
   |   |   ip-addr2: 255.255.255.255
   |   |   subnet2: 255.255.255.255
   |   |   ip-addr3: 255.255.255.255
   |   |   subnet3: 255.255.255.255
   |   |   serial: FFFFFFF
   |   |   FW Version: 4.0
   |   |   FPGA Version: 20.0
   |   |   
   |   |   Time sources: internal, external, gpsdo
   |   |   Clock sources: internal, external, gpsdo
   |   |   Sensors: ref_locked
   |   |     _____________________________________________________
   |   |    /
   |   |   |       RX DSP: 0
   |   |   |   Freq range: -100.000 to 100.000 MHz
   |   |     _____________________________________________________
   |   |    /
   |   |   |       RX DSP: 1
   |   |   |   Freq range: -100.000 to 100.000 MHz
   |   |     _____________________________________________________
   |   |    /
   |   |   |       RX Dboard: A
   |   |   |   ID: SBX (0x0054)
   |   |   |   Serial: FFFFFF
   |   |   |     _____________________________________________________
   |   |   |    /
   |   |   |   |       RX Frontend: 0
   |   |   |   |   Name: SBXv3 RX
   |   |   |   |   Antennas: TX/RX, RX2, CAL
   |   |   |   |   Sensors: lo_locked
   |   |   |   |   Freq range: 400.000 to 4400.000 MHz
   |   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
   |   |   |   |   Bandwidth range: 40000000.0 to 40000000.0 step 0.0 Hz
   |   |   |   |   Connection Type: IQ
   |   |   |   |   Uses LO offset: No
   |   |   |     _____________________________________________________
   |   |   |    /
   |   |   |   |       RX Codec: A
   |   |   |   |   Name: ads62p48
   |   |   |   |   Gain range digital: 0.0 to 6.0 step 0.5 dB
   |   |     _____________________________________________________
   |   |    /
   |   |   |       RX Dboard: B
   |   |   |   ID: SBX (0x0054)
   |   |   |   Serial: FFFFFF
   |   |   |     _____________________________________________________
   |   |   |    /
   |   |   |   |       RX Frontend: 0
   |   |   |   |   Name: SBXv3 RX
   |   |   |   |   Antennas: TX/RX, RX2, CAL
   |   |   |   |   Sensors: lo_locked
   |   |   |   |   Freq range: 400.000 to 4400.000 MHz
   |   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
   |   |   |   |   Bandwidth range: 40000000.0 to 40000000.0 step 0.0 Hz
   |   |   |   |   Connection Type: IQ
   |   |   |   |   Uses LO offset: No
   |   |   |     _____________________________________________________
   |   |   |    /
   |   |   |   |       RX Codec: B
   |   |   |   |   Name: ads62p48
   |   |   |   |   Gain range digital: 0.0 to 6.0 step 0.5 dB
   |   |     _____________________________________________________
   |   |    /
   |   |   |       TX DSP: 0
   |   |   |   Freq range: -100.000 to 100.000 MHz
   |   |     _____________________________________________________
   |   |    /
   |   |   |       TX DSP: 1
   |   |   |   Freq range: -100.000 to 100.000 MHz
   |   |     _____________________________________________________
   |   |    /
   |   |   |       TX Dboard: A
   |   |   |   ID: SBX (0x0055)
   |   |   |   Serial: FFFFFF
   |   |   |     _____________________________________________________
   |   |   |    /
   |   |   |   |       TX Frontend: 0
   |   |   |   |   Name: SBXv3 TX
   |   |   |   |   Antennas: TX/RX, CAL
   |   |   |   |   Sensors: lo_locked
   |   |   |   |   Freq range: 400.000 to 4400.000 MHz
   |   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
   |   |   |   |   Bandwidth range: 40000000.0 to 40000000.0 step 0.0 Hz
   |   |   |   |   Connection Type: QI
   |   |   |   |   Uses LO offset: No
   |   |   |     _____________________________________________________
   |   |   |    /
   |   |   |   |       TX Codec: A
   |   |   |   |   Name: ad9146
   |   |   |   |   Gain Elements: None
   |   |     _____________________________________________________
   |   |    /
   |   |   |       TX Dboard: B
   |   |   |   ID: SBX (0x0055)
   |   |   |   Serial: FFFFFF
   |   |   |     _____________________________________________________
   |   |   |    /
   |   |   |   |       TX Frontend: 0
   |   |   |   |   Name: SBXv3 TX
   |   |   |   |   Antennas: TX/RX, CAL
   |   |   |   |   Sensors: lo_locked
   |   |   |   |   Freq range: 400.000 to 4400.000 MHz
   |   |   |   |   Gain range PGA0: 0.0 to 31.5 step 0.5 dB
   |   |   |   |   Bandwidth range: 40000000.0 to 40000000.0 step 0.0 Hz
   |   |   |   |   Connection Type: QI
   |   |   |   |   Uses LO offset: No
   |   |   |     _____________________________________________________
   |   |   |    /
   |   |   |   |       TX Codec: B
   |   |   |   |   Name: ad9146
   |   |   |   |   Gain Elements: None

UHD FFT

Try the UHD_FFT demo that comes with GNU Radio

1. Connect one antenna to RX2 on the left Daughterboard (Daughterboard A)

Xseries quickstart figure 26.png

2.From the terminal/command window: 

   $ uhd_fft
Xseries quickstart figure 27.png
Xseries quickstart figure 28.png
Retrieved from "https://kb.ettus.com/index.php?title=USRP_X_Series_Quick_Start_(Daughterboard_Installation)&oldid=2641"