Difference between revisions of "E310/E312"

From Ettus Knowledge Base
Jump to: navigation, search
(→‎Interfaces and Connectivity)
(→‎Interfaces and Connectivity)
Line 405: Line 405:
 
*Host USB support
 
*Host USB support
 
*9-axis IMU
 
*9-axis IMU
 +
 +
===Front Panel===
 +
{|
 +
| style="width:50%" |
 +
*RF A Group
 +
**TX/RX LED: Indicates that data is streaming on the TX/RX channel on frontend side A
 +
**RX2 LED: Indicates that data is streaming on the RX2 channel on frontend side A
 +
*RF B Group
 +
**TX/RX LED: Indicates that data is streaming on the TX/RX channel on frontend B
 +
**RX2 LED: Indicates that data is streaming on the RX2 channel on frontend B
 +
*PWR: Power switch with integrated status LED, for status description see below.
 +
*SYNC: Input port for external PPS signal
 +
*GPS: Connection for the GPS antenna
 +
*AUDIO: Audio input / output
 +
 +
The status LED in the power switch indicates the power and charge status. It's behavior is firmware version dependent.
 +
 +
*Version 1 (original E310)
 +
**Off: Indicates device is off and not charging
 +
**Solid Red: Indicates device is charging
 +
**Solid Green: Indicates device is on
 +
**Fast Blinking Red: Indicates an error code
 +
***1 - Low voltage error
 +
***2 - Regulator low voltage error
 +
***3 - FPGA power error
 +
***4 - DRAM power error
 +
***5 - 1.8V rail power error
 +
***6 - 3.3V rail power error
 +
***7 - Daughterboard / TX power error
 +
***9 - Temperature error
 +
*Version 2 (E312 and upgraded E310)
 +
**Off: Indicates device is off and not charging
 +
**Slow Blinking Green: Indicates device is off and charging
 +
**Fast Blinking Green: Indicates device is on and charging
 +
**Solid Green: Indicates device is on (and not charging, if E312)
 +
**Solid Orange: Indicates device is on and discharging
 +
**Fast Blinking Orange: Indicates device is on, discharging, and charge is below 10% charge
 +
**Fast Blinking Red: Indicates an error code
 +
***1 - Low voltage error
 +
***2 - Regulator low voltage error
 +
***3 - FPGA power error
 +
***4 - DRAM power error
 +
***5 - 1.8V rail power error
 +
***6 - 3.3V rail power error
 +
***7 - Daughterboard / TX power error
 +
***8 - Charger error
 +
***9 - Charger temperature error
 +
***10 - Battery low error
 +
***11 - Fuel Gauge temperature error
 +
***12 - Global (case) temperature error
 +
 +
| style="vertical-align:top" | [[File:e3x0 fp overlay.png]]
 +
|}
 +
 +
===Rear Panel===
 +
{|
 +
| style="width:50%" |
 +
*PWR: Locking connector (Kycon KLDHCX-0202-A-LT) for the USRP-E Series power supply
 +
*1G ETH: RJ45 port for Ethernet interfaces
 +
*USB: USB 2.0 Port
 +
*SERIAL: Micro USB connection for serial uart console
 +
 +
 +
| style="vertical-align:top" | [[File:e3x0 rp overlay.png]]
 +
 +
|}
  
  

Revision as of 14:44, 24 May 2016

Device Overview

The USRP E310 offers a portable stand-alone SDR platform designed for field deployment. The flexible 2x2 MIMO AD9361 transceiver from Analog Devices provides up to 56 MHz of instantaneous bandwidth and spans frequencies from 70 MHz – 6 GHz to cover multiple bands of interest.

Key Features

E310

  • Xilinx Zynq 7020 SoC: 7 Series FPGA with ARM Cortex A9 667 MHz dual-core processor
  • Analog Devices AD9361 RFIC direct-conversion transceiver
  • Frequency range: 70 MHz - 6 GHz
  • Up to 56 MHz of instantaneous bandwidth
  • 2x2 MIMO transceiver
  • Up to 10 MS/s sample data transfer rate to ARM processor
  • RX, TX filter banks
  • Integrated GPS receiver
  • 9-axis inertial measurement unit
  • RF Network on Chip (RFNoC™) FPGA development framework support
Product e310.png

E312

  • Battery Operated
  • Xilinx Zynq 7020 SoC: 7 Series FPGA with ARM Cortex A9 866 MHz dual-core processor
  • Analog Devices AD9361 RFIC direct-conversion transceiver
  • Frequency range: 70 MHz - 6 GHz
  • Up to 56 MHz of instantaneous bandwidth
  • 2x2 MIMO transceiver
  • Up to 10 MS/s sample data transfer rate to ARM processor
  • RX, TX filter banks
  • Integrated GPS receiver
  • 9-axis inertial measurement unit
  • RF Network on Chip (RFNoC™) FPGA development framework support
Product e312.png

RF Specifications

RF Performance

  • SSB/LO Suppression -35/50 dBc
  • Phase Noise 3.5 GHz 1.0 deg RMS
  • Phase Noise 6 GHz 1.5 deg RMS
  • Power Output >10dBm
  • IIP3 (@ typ NF) -20dBm
  • Typical Noise Figure <8dB

Hardware Specifications

  • Ettus Research recommends to always use the latest stable version of UHD

E310

  • Current Hardware Revision: 1
  • Minimum version of UHD required: 3.8.0
  • Required version on the host computer must match what is running on the E310

E312

  • Current Hardware Revision: 1
  • Minimum version of UHD required: 3.8.5
  • Required version on the host computer must match what is running on the E312

Physical Specifications

Dimensions

  • 133 x 68 x 26.4 mm

Environmental Specifications

Operating Temperature Range

  • E310 0-40 °C

Schematics

E310

E310 Schematics

E310 DB

E310 Architecture

Key Component Datasheets

Part Number Description Schematic ID (Page)
Motherboard
TXS02612RTWR SDIO PORT EXPANDER U23 (2)
XC7Z020-1CLG484CES9919 FPGA U11 (2,3,4,8,11,13)
Xilinx Zynq Product Page FPGA -
USB3340-EZK-TR ULPI Transceiver U33 (5)
AK4571VQP Audio CODEC U30 (6)
FT230XQ-R UART Interface U32 (6)
88E1512 Gigabit Ethernet Transceiver U13 (7)
24LC024/SN EEPROM U5 (9)
DS1339,SM Real-Time Clock U6 (9)
ADT7408 Temperature Sensor U8 (9)
MPU-9150 Motion Processing Unit U3 (9)
InvenSense MPU-9150 Product Page Motion Processing Unit U3 (9)
BMP180 Digital pressure sensor U4 (9)
BQ24192 Adapter Charger U1 (10)
TPS54478 Step-Down Switcher U20 (10)
MAX6510HAUT-T Temperature Switches U35 (10)
ATTINY88-MU Microcontroller U18 (10)
TPS61253YFF Step-Up Converter U19 (10)
Daughterboard
Part Number Description Schematic ID (Page)
AD9361 Product Page 2 x 2 RF Agile Transceiver U8 (3)
24AA256 EEPROM U15 (2)
TC-1-43A+ RF Transformer T6 (3); T5 (3); T4 (3)
TC1-1-13M+ RF Transformer T7 (3); T10 (3); T1 (3)
TPS62140 Step-Down Converter U19 (4)
ADP1753ACPZ-R7 Linear Regulator U17 (4); U18 (4)
SGA-4563Z MMIC AMPLIFIER U12 (5); U4 (5)
SKY13418-485LF Antenna Switch U13 (5); U3 (5); U16 (5); U2 (5); U10 (6); U5 (6)
SKY13373-460LF SP3T Switch U11 (6); U9 (6); U6 (6); U7 (6); SW4 (7); SW1 (7)
MGA-81563 Amplifier U14 (5); U1 (5)
LFCN-5850+ Low Pass Filter FL32 (5); FL1 (5)
LFCN-2750+ Low Pass Filter FL37 (5); FL4 (5)
LFCN-2250+ Low Pass Filter FL23 (6); FL20 (6)
LFCN-1700+ Low Pass Filter FL40 (5); FL2 (5)
LFCN-1575+ Low Pass Filter FL25 (6); FL17 (6)
LFCN-1000+ Low Pass Filter FL33 (5); FL9 (5); FL27 (6); FL15 (6)
LFCN-575+ Low Pass Filter FL36 (5); FL5 (5)
LFCN-530+ Low Pass Filter FL29 (6); FL13 (6)
LFCN-400+ Low Pass Filter FL38 (5); FL3 (5); FL30 (6); FL11 (6)
LFCN-225 Low Pass Filter FL39 (5); FL6 (5)
LFCN-160+ Low Pass Filter FL34 (5); FL8 (5)
LFCN-80+ Low Pass Filter FL35 (5); FL7 (5)
HFCN-1600+ High Pass Filter FL22 (6); FL19 (6)
HFCN-1100+ High Pass Filter FL24 (6); FL16 (6)
HFCN-650+ High Pass Filter FL26 (6); FL14 (6)
HFCN-440+ High Pass Filter FL28 (6); FL12 (6)
BFCN-2435+ Bandpass Filter FL21 (6); FL18 (6)
FDG6301N Dual N-Channel, Digital FET Q8 (7); Q5 (7)
HSMS-8202 Mixer Diodes CR1 (7); CR2 (7); CR3 (7); CR4 (7)
LP5900TL Linear Regulator U25 (8)
ADP150AUJZ-3.0 Linear Regulator U22 (8)
AD5662RBJ 16-Bit nanoDAC U21 (8)
SN74AUP1T57 Voltage Translator U27 (8); U28 (8); U29 (8)

Request a detailed whitepaper covering features and components from info@ettus.com

Mechanical Information

Weight

  • Partial Enclosure 225 g
  • Full Enclosure 375 g

Drawings

FPGA

  • Utilization statistics are subject to change between UHD releases, current as of UHD 3.9.4

E310/E312

1. Slice Logic
--------------

+----------------------------+-------+-----------+-------+
|          Site Type         |  Used | Available | Util% |
+----------------------------+-------+-----------+-------+
| Slice LUTs                 | 36203 |     53200 | 68.05 |
|   LUT as Logic             | 28108 |     53200 | 52.83 |
|   LUT as Memory            |  8095 |     17400 | 46.52 |
|     LUT as Distributed RAM |   870 |           |       |
|     LUT as Shift Register  |  7225 |           |       |
| Slice Registers            | 36562 |    106400 | 34.36 |
|   Register as Flip Flop    | 36562 |    106400 | 34.36 |
|   Register as Latch        |     0 |    106400 |  0.00 |
| F7 Muxes                   |   376 |     26600 |  1.41 |
| F8 Muxes                   |   125 |     13300 |  0.93 |
+----------------------------+-------+-----------+-------+

3. Memory
---------

+-------------------+------+-----------+-------+
|     Site Type     | Used | Available | Util% |
+-------------------+------+-----------+-------+
| Block RAM Tile    |   97 |       140 | 69.28 |
|   RAMB36/FIFO*    |   90 |       140 | 64.28 |
|     RAMB36E1 only |   90 |           |       |
|   RAMB18          |   14 |       280 |  5.00 |
|     RAMB18E1 only |   14 |           |       |
+-------------------+------+-----------+-------+
* Note: Each Block RAM Tile only has one FIFO logic available and therefore can accommodate only one FIFO36E1 or one FIFO18E1. However, if a FIFO18E1 occupies a Block RAM Tile, that tile can still accommodate a RAMB18E1


4. DSP
------

+----------------+------+-----------+-------+
|    Site Type   | Used | Available | Util% |
+----------------+------+-----------+-------+
| DSPs           |  120 |       220 | 54.54 |
|   DSP48E1 only |  120 |           |       |
+----------------+------+-----------+-------+

Interfaces and Connectivity

  • 10/100/1000 BASE-T Ethernet
  • Stereo audio out, mono mic in
  • Integrated GPS receiver
  • Host USB support
  • 9-axis IMU

Front Panel

  • RF A Group
    • TX/RX LED: Indicates that data is streaming on the TX/RX channel on frontend side A
    • RX2 LED: Indicates that data is streaming on the RX2 channel on frontend side A
  • RF B Group
    • TX/RX LED: Indicates that data is streaming on the TX/RX channel on frontend B
    • RX2 LED: Indicates that data is streaming on the RX2 channel on frontend B
  • PWR: Power switch with integrated status LED, for status description see below.
  • SYNC: Input port for external PPS signal
  • GPS: Connection for the GPS antenna
  • AUDIO: Audio input / output

The status LED in the power switch indicates the power and charge status. It's behavior is firmware version dependent.

  • Version 1 (original E310)
    • Off: Indicates device is off and not charging
    • Solid Red: Indicates device is charging
    • Solid Green: Indicates device is on
    • Fast Blinking Red: Indicates an error code
      • 1 - Low voltage error
      • 2 - Regulator low voltage error
      • 3 - FPGA power error
      • 4 - DRAM power error
      • 5 - 1.8V rail power error
      • 6 - 3.3V rail power error
      • 7 - Daughterboard / TX power error
      • 9 - Temperature error
  • Version 2 (E312 and upgraded E310)
    • Off: Indicates device is off and not charging
    • Slow Blinking Green: Indicates device is off and charging
    • Fast Blinking Green: Indicates device is on and charging
    • Solid Green: Indicates device is on (and not charging, if E312)
    • Solid Orange: Indicates device is on and discharging
    • Fast Blinking Orange: Indicates device is on, discharging, and charge is below 10% charge
    • Fast Blinking Red: Indicates an error code
      • 1 - Low voltage error
      • 2 - Regulator low voltage error
      • 3 - FPGA power error
      • 4 - DRAM power error
      • 5 - 1.8V rail power error
      • 6 - 3.3V rail power error
      • 7 - Daughterboard / TX power error
      • 8 - Charger error
      • 9 - Charger temperature error
      • 10 - Battery low error
      • 11 - Fuel Gauge temperature error
      • 12 - Global (case) temperature error
 e3x0 fp overlay.png

Rear Panel

  • PWR: Locking connector (Kycon KLDHCX-0202-A-LT) for the USRP-E Series power supply
  • 1G ETH: RJ45 port for Ethernet interfaces
  • USB: USB 2.0 Port
  • SERIAL: Micro USB connection for serial uart console


 e3x0 rp overlay.png


GPIO

Pin Mapping

  • Pin 1: +3.3V
  • Pin 2: Reserved
  • Pin 3: Data[5]
  • Pin 4: Reserved
  • Pin 5: Data[4]
  • Pin 6: Data[0]
  • Pin 7: Data[3]
  • Pin 8: Data[1]
  • Pin 9: 0V
  • Pin 10: Data[2]
 e3x0 gpio conn.png

Audio

  • The E3x0 2.5 mm Audio Jack TRRS pins are assigned as follows: Tip=Mic, Ring1=Right, Ring2=Left, Sleeve=GND.
  • The Left/Right audio outputs are compatible with typical low-impedance headphones (16 to 32 Ohms). The Microphone pin provides approximately 2 mA bias at 2.2 V when not suspended. A variety of pin configurations can be found on commonly available headsets, so an adapter may be required.
 TRRS.png

Certifications

RoHS

As of December 1st, 2010 all Ettus Research products are RoHS compliant unless otherwise noted. More information can be found at http://ettus.com/legal/rohs-information

Certificate of Volatility

E310

E312

Downloads

FPGA Images

FPGA Images Read Me

FPGA Resources

UHD Stable Binaries

UHD Source Code on Github

Retrieved from "https://kb.ettus.com/index.php?title=E310/E312&oldid=2689"