Difference between revisions of "E320"

Revision as of 14:42, 14 December 2018 (view source) Ettus (Talk | contribs) (→‎Interfaces and Connectivity) ← Older edit		Revision as of 11:56, 25 March 2019 (view source) Ettus (Talk | contribs) (→‎Interfaces and Connectivity) Newer edit →
Line 119:		Line 119:
	|}		|}
		+
		+	===Power Connector===
		+	Model: PDP-40 by CUI Inc.
		+
		+	Power plug connectors for custom power harnesses can be purchased here: https://www.digikey.com/products/en?KeyWords=CP-7340-ND&WT.z_cid=sp_102_buynow
		+
		+	Assembly instructions: [[Media:pdp-40.pdf]]
		+
		+	====Pin Detail====
		+	* Pins #1 / #2: 12v
		+	* Pins #3 / #4: Ground
		+
		+	[[File:pdp 40 power detail.png]]
	==Certifications==		==Certifications==

---

Revision as of 11:56, 25 March 2019

Device Overview

The USRP E320 brings performance to embedded software defined radios by offering four times more FPGA resources compared to the USRP E31x devices. The USRP E320 also introduces improvements in streaming, synchronization, integration, fault-recovery, and remote management capability. This field deployable SDR continues to use the flexible 2x2 MIMO AD9361 transceiver from Analog Devices, which covers frequencies from 70 MHz – 6 GHz and provides up to 56 MHz of instantaneous bandwidth.

Key Features

E320

Xilinx Zynq 7045 SoC 7 Series FPGA with 2GB DDR3 RAM ARM Cortex A9 800 MHz dual-core processor Analog Devices AD9361 RFIC direct-conversion transceiver Frequency range: 70 MHz - 6 GHz Up to 56 MHz of instantaneous bandwidth 2x2 MIMO transceiver Up to 10 MS/s sample data transfer rate to ARM processor Up to 61.44 MS/s sample data transfer to host (10Gb/SFP+) RX, TX filter banks Integrated GPSDO 9-axis inertial measurement unit RF Network on Chip (RFNoC™) FPGA development framework support Board-only and Full Enclosure Options

RF Specifications

RF Performance

• Power Output >10dBm
• IIP3 (@ typical NF) -20dBm
• Typical Receive Noise Figure <8dB

Input Power Levels

• The maximum input power for the E320 is -15 dBm.

Hardware Specifications

• Ettus Research recommends to always use the latest stable version of UHD
• UHD version on the host computer must match what is running on the E320

E320

• Current Hardware Revision: 1
• Minimum version of UHD required: 3.14.0.0

Physical Specifications

Dimensions

E320 board-only with heatsink

• 173 x 100 x 36 mm

E320 Full enclosure

• 175 x 106 x 38 mm

Environmental Specifications

Operating Temperature Range

• 0-45 °C

Non-Operating Temperature Range

• -40-85 °C

Operating Humidity Range

• 10% to 90% non-condensing

Non-Operating Humidity Range

• 5% to 95% non-condensing

Mechanical Information

Weight

E320 board-only with heatsink

• 0.16 kg

E320 Full enclosure

• 0.86 kg

Frontend Specifications

Tuning

The RF frontend has individually tunable receive and transmit chains. Both transmit and receive can be used in a MIMO configuration. For the MIMO case, both receive frontends share the RX LO, and both transmit frontends share the TX LO. Each LO is tunable between 50 MHz and 6 GHz.

Gains

All frontends have individual analog gain controls. The receive frontends have 76 dB of available gain; and the transmit frontends have 89.8 dB of available gain. Gain settings are application specific, but it is recommended that users consider using at least half of the available gain to get reasonable dynamic range.

Interfaces and Connectivity

• RJ45 (1 GbE)
• SFP+ (1/10 GbE, Aurora)
• Type A USB Host
• Micro-USB (serial console, JTAG)
• GPIO
• Integrated GPSDO
• 9-axis IMU

Front Panel

PWR: Power button RF A Group TX/RX LED: Indicates that data is streaming on the TX/RX channel on frontend side A RX2 LED: Indicates that data is streaming on the RX2 channel on frontend side A RF B Group TX/RX LED: Indicates that data is streaming on the TX/RX channel on frontend B RX2 LED: Indicates that data is streaming on the RX2 channel on frontend B PPS IN: Input port for external PPS signal REF IN: Input port for external 10 MHz signal GPS ANT: Connection for the GPS antenna

Rear Panel

POWER: 10-14v DC Power connector GPIO: Mini-HDMI connector for GPIO USB: USB 2.0 Port 1G ETH: RJ45 port for remote management SFP+: SFP+ connection for sample streaming CONSOLE JTAG: Micro USB connection for serial UART/JTAG console

Power Connector

Model: PDP-40 by CUI Inc.

Power plug connectors for custom power harnesses can be purchased here: https://www.digikey.com/products/en?KeyWords=CP-7340-ND&WT.z_cid=sp_102_buynow

Assembly instructions: Media:pdp-40.pdf

Pin Detail

• Pins #1 / #2: 12v
• Pins #3 / #4: Ground

Certifications

RoHS

As of December 1st, 2010 all Ettus Research products are RoHS compliant unless otherwise noted. More information can be found at http://ettus.com/legal/rohs-information

China RoHS

Management Methods for Controlling Pollution Caused by Electronic Information Products Regulation

Chinese Customers

National Instruments is in compliance with the Chinese policy on the Restriction of Hazardous Substances (RoHS) used in Electronic Information Products. For more information about the National Instruments China RoHS compliance, visit ni.com/environment/rohs_china.