Difference between revisions of "E310/E312"

Revision as of 14:46, 24 May 2016 (view source) Ettus (Talk | contribs) (→‎Front Panel) ← Older edit		Revision as of 14:47, 24 May 2016 (view source) Ettus (Talk | contribs) (→‎Rear Panel) Newer edit →
Line 463:		Line 463:
	{|		{|
	| style="width:50%" |		| style="width:50%" |
−	*PWR: Locking connector (Kycon KLDHCX-0202-A-LT) for the USRP-E Series power supply	+	*'''PWR:''' Locking connector (Kycon KLDHCX-0202-A-LT) for the USRP-E Series power supply
−	*1G ETH: RJ45 port for Ethernet interfaces	+	*'''1G ETH:''' RJ45 port for Ethernet interfaces
−	*USB: USB 2.0 Port	+	*'''USB:''' USB 2.0 Port
−	*SERIAL: Micro USB connection for serial uart console	+	*'''SERIAL:''' Micro USB connection for serial uart console
Line 472:		Line 472:
	|}		|}
−
	===GPIO===		===GPIO===

---

Revision as of 14:47, 24 May 2016

Device Overview

The USRP E310 offers a portable stand-alone SDR platform designed for field deployment. The flexible 2x2 MIMO AD9361 transceiver from Analog Devices provides up to 56 MHz of instantaneous bandwidth and spans frequencies from 70 MHz – 6 GHz to cover multiple bands of interest.

Key Features

E310

Xilinx Zynq 7020 SoC: 7 Series FPGA with ARM Cortex A9 667 MHz dual-core processor Analog Devices AD9361 RFIC direct-conversion transceiver Frequency range: 70 MHz - 6 GHz Up to 56 MHz of instantaneous bandwidth 2x2 MIMO transceiver Up to 10 MS/s sample data transfer rate to ARM processor RX, TX filter banks Integrated GPS receiver 9-axis inertial measurement unit RF Network on Chip (RFNoC™) FPGA development framework support

E312

Battery Operated Xilinx Zynq 7020 SoC: 7 Series FPGA with ARM Cortex A9 866 MHz dual-core processor Analog Devices AD9361 RFIC direct-conversion transceiver Frequency range: 70 MHz - 6 GHz Up to 56 MHz of instantaneous bandwidth 2x2 MIMO transceiver Up to 10 MS/s sample data transfer rate to ARM processor RX, TX filter banks Integrated GPS receiver 9-axis inertial measurement unit RF Network on Chip (RFNoC™) FPGA development framework support

RF Specifications

RF Performance

• SSB/LO Suppression -35/50 dBc
• Phase Noise 3.5 GHz 1.0 deg RMS
• Phase Noise 6 GHz 1.5 deg RMS
• Power Output >10dBm
• IIP3 (@ typ NF) -20dBm
• Typical Noise Figure <8dB

Hardware Specifications

• Ettus Research recommends to always use the latest stable version of UHD

E310

• Current Hardware Revision: 1
• Minimum version of UHD required: 3.8.0
• Required version on the host computer must match what is running on the E310

E312

• Current Hardware Revision: 1
• Minimum version of UHD required: 3.8.5
• Required version on the host computer must match what is running on the E312

Physical Specifications

Dimensions

• 133 x 68 x 26.4 mm

Environmental Specifications

Operating Temperature Range

• E310 0-40 °C

Schematics

E310

E310 Schematics

E310 DB

E310 Architecture

Key Component Datasheets

Part Number	Description	Schematic ID (Page)
Motherboard
TXS02612RTWR	SDIO PORT EXPANDER	U23 (2)
XC7Z020-1CLG484CES9919	FPGA	U11 (2,3,4,8,11,13)
Xilinx Zynq Product Page	FPGA	-
USB3340-EZK-TR	ULPI Transceiver	U33 (5)
AK4571VQP	Audio CODEC	U30 (6)
FT230XQ-R	UART Interface	U32 (6)
88E1512	Gigabit Ethernet Transceiver	U13 (7)
24LC024/SN	EEPROM	U5 (9)
DS1339,SM	Real-Time Clock	U6 (9)
ADT7408	Temperature Sensor	U8 (9)
MPU-9150	Motion Processing Unit	U3 (9)
InvenSense MPU-9150 Product Page	Motion Processing Unit	U3 (9)
BMP180	Digital pressure sensor	U4 (9)
BQ24192	Adapter Charger	U1 (10)
TPS54478	Step-Down Switcher	U20 (10)
MAX6510HAUT-T	Temperature Switches	U35 (10)
ATTINY88-MU	Microcontroller	U18 (10)
TPS61253YFF	Step-Up Converter	U19 (10)
Daughterboard
Part Number	Description	Schematic ID (Page)
AD9361 Product Page	2 x 2 RF Agile Transceiver	U8 (3)
24AA256	EEPROM	U15 (2)
TC-1-43A+	RF Transformer	T6 (3); T5 (3); T4 (3)
TC1-1-13M+	RF Transformer	T7 (3); T10 (3); T1 (3)
TPS62140	Step-Down Converter	U19 (4)
ADP1753ACPZ-R7	Linear Regulator	U17 (4); U18 (4)
SGA-4563Z	MMIC AMPLIFIER	U12 (5); U4 (5)
SKY13418-485LF	Antenna Switch	U13 (5); U3 (5); U16 (5); U2 (5); U10 (6); U5 (6)
SKY13373-460LF	SP3T Switch	U11 (6); U9 (6); U6 (6); U7 (6); SW4 (7); SW1 (7)
MGA-81563	Amplifier	U14 (5); U1 (5)
LFCN-5850+	Low Pass Filter	FL32 (5); FL1 (5)
LFCN-2750+	Low Pass Filter	FL37 (5); FL4 (5)
LFCN-2250+	Low Pass Filter	FL23 (6); FL20 (6)
LFCN-1700+	Low Pass Filter	FL40 (5); FL2 (5)
LFCN-1575+	Low Pass Filter	FL25 (6); FL17 (6)
LFCN-1000+	Low Pass Filter	FL33 (5); FL9 (5); FL27 (6); FL15 (6)
LFCN-575+	Low Pass Filter	FL36 (5); FL5 (5)
LFCN-530+	Low Pass Filter	FL29 (6); FL13 (6)
LFCN-400+	Low Pass Filter	FL38 (5); FL3 (5); FL30 (6); FL11 (6)
LFCN-225	Low Pass Filter	FL39 (5); FL6 (5)
LFCN-160+	Low Pass Filter	FL34 (5); FL8 (5)
LFCN-80+	Low Pass Filter	FL35 (5); FL7 (5)
HFCN-1600+	High Pass Filter	FL22 (6); FL19 (6)
HFCN-1100+	High Pass Filter	FL24 (6); FL16 (6)
HFCN-650+	High Pass Filter	FL26 (6); FL14 (6)
HFCN-440+	High Pass Filter	FL28 (6); FL12 (6)
BFCN-2435+	Bandpass Filter	FL21 (6); FL18 (6)
FDG6301N	Dual N-Channel, Digital FET	Q8 (7); Q5 (7)
HSMS-8202	Mixer Diodes	CR1 (7); CR2 (7); CR3 (7); CR4 (7)
LP5900TL	Linear Regulator	U25 (8)
ADP150AUJZ-3.0	Linear Regulator	U22 (8)
AD5662RBJ	16-Bit nanoDAC	U21 (8)
SN74AUP1T57	Voltage Translator	U27 (8); U28 (8); U29 (8)

Request a detailed whitepaper covering features and components from info@ettus.com

Mechanical Information

Weight

• Partial Enclosure 225 g
• Full Enclosure 375 g

Drawings

• E310 Drawings - File:E310 Dimensional Sketches.pdf

FPGA

• Utilization statistics are subject to change between UHD releases, current as of UHD 3.9.4

E310/E312

1. Slice Logic
--------------

+----------------------------+-------+-----------+-------+
|          Site Type         |  Used | Available | Util% |
+----------------------------+-------+-----------+-------+
| Slice LUTs                 | 36203 |     53200 | 68.05 |
|   LUT as Logic             | 28108 |     53200 | 52.83 |
|   LUT as Memory            |  8095 |     17400 | 46.52 |
|     LUT as Distributed RAM |   870 |           |       |
|     LUT as Shift Register  |  7225 |           |       |
| Slice Registers            | 36562 |    106400 | 34.36 |
|   Register as Flip Flop    | 36562 |    106400 | 34.36 |
|   Register as Latch        |     0 |    106400 |  0.00 |
| F7 Muxes                   |   376 |     26600 |  1.41 |
| F8 Muxes                   |   125 |     13300 |  0.93 |
+----------------------------+-------+-----------+-------+

3. Memory
---------

+-------------------+------+-----------+-------+
|     Site Type     | Used | Available | Util% |
+-------------------+------+-----------+-------+
| Block RAM Tile    |   97 |       140 | 69.28 |
|   RAMB36/FIFO*    |   90 |       140 | 64.28 |
|     RAMB36E1 only |   90 |           |       |
|   RAMB18          |   14 |       280 |  5.00 |
|     RAMB18E1 only |   14 |           |       |
+-------------------+------+-----------+-------+
* Note: Each Block RAM Tile only has one FIFO logic available and therefore can accommodate only one FIFO36E1 or one FIFO18E1. However, if a FIFO18E1 occupies a Block RAM Tile, that tile can still accommodate a RAMB18E1


4. DSP
------

+----------------+------+-----------+-------+
|    Site Type   | Used | Available | Util% |
+----------------+------+-----------+-------+
| DSPs           |  120 |       220 | 54.54 |
|   DSP48E1 only |  120 |           |       |
+----------------+------+-----------+-------+

Interfaces and Connectivity

• 10/100/1000 BASE-T Ethernet
• Stereo audio out, mono mic in
• Integrated GPS receiver
• Host USB support
• 9-axis IMU

Front Panel

RF A Group TX/RX LED: Indicates that data is streaming on the TX/RX channel on frontend side A RX2 LED: Indicates that data is streaming on the RX2 channel on frontend side A RF B Group TX/RX LED: Indicates that data is streaming on the TX/RX channel on frontend B RX2 LED: Indicates that data is streaming on the RX2 channel on frontend B PWR: Power switch with integrated status LED, for status description see below. SYNC: Input port for external PPS signal GPS: Connection for the GPS antenna AUDIO: Audio input / output The status LED in the power switch indicates the power and charge status. It's behavior is firmware version dependent. Version 1 (original E310) Off: Indicates device is off and not charging Solid Red: Indicates device is charging Solid Green: Indicates device is on Fast Blinking Red: Indicates an error code 1 - Low voltage error 2 - Regulator low voltage error 3 - FPGA power error 4 - DRAM power error 5 - 1.8V rail power error 6 - 3.3V rail power error 7 - Daughterboard / TX power error 9 - Temperature error Version 2 (E312 and upgraded E310) Off: Indicates device is off and not charging Slow Blinking Green: Indicates device is off and charging Fast Blinking Green: Indicates device is on and charging Solid Green: Indicates device is on (and not charging, if E312) Solid Orange: Indicates device is on and discharging Fast Blinking Orange: Indicates device is on, discharging, and charge is below 10% charge Fast Blinking Red: Indicates an error code 1 - Low voltage error 2 - Regulator low voltage error 3 - FPGA power error 4 - DRAM power error 5 - 1.8V rail power error 6 - 3.3V rail power error 7 - Daughterboard / TX power error 8 - Charger error 9 - Charger temperature error 10 - Battery low error 11 - Fuel Gauge temperature error 12 - Global (case) temperature error

Rear Panel

PWR: Locking connector (Kycon KLDHCX-0202-A-LT) for the USRP-E Series power supply 1G ETH: RJ45 port for Ethernet interfaces USB: USB 2.0 Port SERIAL: Micro USB connection for serial uart console

GPIO

Pin Mapping Pin 1: +3.3V Pin 2: Reserved Pin 3: Data[5] Pin 4: Reserved Pin 5: Data[4] Pin 6: Data[0] Pin 7: Data[3] Pin 8: Data[1] Pin 9: 0V Pin 10: Data[2]

• Please see the E3x0/X3x0 GPIO API for information on configuring and using the GPIO bus.

Audio

The E3x0 2.5 mm Audio Jack TRRS pins are assigned as follows: Tip=Mic, Ring1=Right, Ring2=Left, Sleeve=GND. The Left/Right audio outputs are compatible with typical low-impedance headphones (16 to 32 Ohms). The Microphone pin provides approximately 2 mA bias at 2.2 V when not suspended. A variety of pin configurations can be found on commonly available headsets, so an adapter may be required.

Certifications

RoHS

As of December 1st, 2010 all Ettus Research products are RoHS compliant unless otherwise noted. More information can be found at http://ettus.com/legal/rohs-information

Certificate of Volatility

E310

• Media:volatility USRP E310 r1.pdf

E312

• Media:USRP E31x CoV.pdf

Downloads

FPGA Images

FPGA Images Read Me

FPGA Resources

UHD Stable Binaries

UHD Source Code on Github